 |
|
MINERAL
TURPENTINE OIL (HPCL)
Prices
|
| 1. |
Colour
(Saybolt) Min |
:
21 |
| 2. |
Colour
(ASTM) Max |
:
- |
| 3. |
Density
at 15 oC gm/ml |
:
30 |
| 4. |
Flash
Point (Abel) oC Min |
:
30 |
| 5. |
Distillation
Range
a) IBP oC Min
b) FBP (Max)
c) Dry Point oC Min |
:
125
: 240
: - |
| 6. |
Aromatic
Content % by Volume |
:
40 Max |
| 7. |
Residue
on evaporation mg/100 ml max |
:
5 |
| 8. |
Copper
stripe corrosion for 3 hrs. at 50 oC |
Not
worse than No. 1 |
HP Solvent Mineral Turpentine 2445
Confirming to ISI Specification No. is : 1978 |
|
|
MINERAL
TURPENTINE LAWS (BPCL)
Prices
|
| 1. |
Colour
(Say bolt) Min) |
:
20 |
| 2. |
Density
at 15 oC gm/ml (Typical) |
:
0.795 |
| 3. |
Flash
Point (Abel) oC Min |
:
35 |
| 4. |
Distillation
Range
a) IBP oC Min
b) FBP oC Max |
:
145
: 205 |
| 5. |
Aromatic
Content % V Max |
:
40 |
| 6. |
Copper
Stripe corrosion for 3 hrs. at 50 oC |
:
Not worse than No. 1 |
| 7. |
Residue
on evaporation m/g 100 ml. max |
:
5 |
BPCL MTL confirm to IS Specification 1745-1978
for Solvent 145/205 Low Aromatic |
| SUPERIOR
KEROSENE OIL
Prices
|
| 1. |
Acidity,
Inorganic |
:
Nil |
| 2. |
Burning
quantity
a) Char value, mg/kg of oil consumed, max
b) Bloom on glass chimney |
:
20
: Not darker than grey |
| 3. |
Colour
(Say blot), min |
:
+10 |
| 4. |
Copper
Stripe corrosion for 3 hrs. at 50 oC |
:
Not worse than No. 1 |
| 5. |
Distillation
a) Percentage recovery below 200 oC. Min
b) Final Point, (Abel), oC, Min |
:
20
: 300 |
| 6. |
Flash
Point, (Abel), oC, Min |
:
35 |
| 7. |
Smoke
Point, mm, min |
:
18** |
| 8. |
Total
Solphur, %Wt, Max |
:
0.25*** |
| LIGHT
DIESEL OIL
Prices
|
| 1. |
Acidity
inorganic |
:
Nil |
| 2. |
Ash
% wt, Max |
:
0.02 |
| 3. |
Carbon
residue
(Ramsbottom) %wt, Max |
:
1.50 |
| 4. |
Pour
Point, Max |
:
12 oC for winter, 18 oC for summer |
| 5. |
Copper
Stripe sorrosion for 3 hrs at 100 oC |
:
Not worse than No. 2 |
| 6. |
Flash
Point (Pensky-Martens) closed cup oC, Min |
:
66 |
| 7. |
Total
Sulphur, % wt, Max |
:
1.80 |
| 8. |
Water
Content, % V. Max |
:
0.25 |
| FURNACE
OIL
Prices
|
| 1. |
Acidity,
inorganic |
:
Nil |
| 2. |
Ash,
% wt., Max |
:
0.1 |
| 3. |
Gross,
Calorific value cal/g |
:
Not limited, but to be reported (typical-10 |
| 4. |
Relative
density at 15/15 oC |
:
Not limited but to be reported (typical-0.950) |
| 5. |
Flash
Point (PMCC) oC Min |
:
66 |
| 6. |
Water
content, % by Vol., Max |
:
0.10 |
| HEXANE
Prices
|
| 1. |
Diatillation
a) Initial Boiling Point oC, min
b) Dry Point, oC Max |
:
63
: 70 |
| 2. |
Composition
a) Aromatics, % V.max
b) Saturates, % V.max |
:
1.0
: 98.5 |
| 3. |
Density
at 25 oC, max |
:
0.687 |
| 4. |
Colour
(Saybolt ) |
:
+30 |
| 5. |
Sulphur
content, ppm, max |
:
75 |
| 6. |
Copper
strip corrosion, 3hrs, at 50 oC, max |
:
1 |
| SBP
55/115
Prices
|
| 1. |
Colour
(satbolt), min |
:
+25 |
| 2. |
Density
at 15 oC, g/ml |
:
To be reported |
| 3. |
Distillation
Range
a) Initial Boiling Point oC, min
b) Dry point, oC, Max |
:
50
: 120 |
| 4. |
Aromatic
content, % Max |
:
35 |
| 5. |
Copper
strip corrosion for 3 hrs. at 50 oC |
:
Not worse than No. 1 |
| 6. |
Residue
on Eveporation, mg/100ml.,Max |
:
5 |
ALPROL (BASE OIL)
Prices
|
|
N12
|
N32
|
N100 |
N150 |
N220 |
N320 |
N450 |
N500
|
| APPEARANCE |
------------------------------BRIGHT
& CLEAR------------------------------
|
| Colour,
ASTM Max. |
1.5 |
1.5 |
4 |
6 |
6 |
6 |
5 |
6 |
| Density
@ 29.5oC |
0.865 |
0.873 |
0.885 |
0.983 |
0.906 |
0.887 |
0.898 |
0.899 |
| Flash
Point, COC oC Min |
160 |
190 |
224 |
240 |
240 |
240 |
270 |
270 |
| Pour
Point, oC Max |
0 |
0 |
0 |
0 |
0 |
0 |
0 |
0 |
Viscosity,
Kinematics, cSt
@ 40 oC
@100 oC |
9.5-19.5 |
29-34 |
90-105 |
140-180 |
245 |
300-340 |
414-505 |
520 |
| Viscosity
Index Min |
95 |
95 |
95 |
90 |
90 |
90 |
90 |
90 |
| BASE
OIL
Prices
|
| Characteristic |
ASTM
METHODS
|
500SN |
BRIGHTSTOCK
150 |
| Aperence |
visual |
C&B |
C&B |
| Viscosity,
@ 40 oC, c |
D-445 |
90-105 |
- |
| Viscosity,
100 oC, cst |
D-445 |
- |
31-33 |
| VI, min |
D-2270 |
95 |
95 |
| Pour Pt,
Max oC |
D-97 |
-9 |
-6 |
| Flash
Pt, (COC), Min oC |
D-92 |
230 |
300 |
| Colour,
Max |
D-1500 |
4.0 |
6.5 |
| HEAVY
CUT RESIDUE
Prices
|
| 1. |
Physical
Appearance |
:
Dark Brown Liquid |
| 2. |
Density
at 15 oC, g/ml |
:
0.8232 |
| 3. |
Acidity
Inorganic |
:
Nil |
| 4. |
Ash
Content (% by Mass) |
:
0.016 |
| 5. |
Gross
Calorific Value (K cal/kg calculated) |
:
10976.92 |
| 6. |
Flash
Point (Abel) Deg C |
:
62 |
| 7. |
Water
Content (% by Volume) |
:
TA |
| 8. |
Distillation
in Deg C
a) Initial Boiling Point
b) 50% Recovery
c) 95% Recovery
d) Final Boiling Point |
:
176
: 233
: 310
: 324 |
| 9. |
Residue
(v/v %) |
:
3.0 |
| 10. |
Recovery
(v/v %) |
:
97 |
| 11. |
Suspended
Particles (v/v %) |
:
1.5 |
| 12. |
Viscosity
(CST) |
:
1.9 |
| |
| HCR
is a good fuel for use in boilers, genset and brick kilns replacing
fuels like HSD, LDO & C9 fuel |
SPECIFICATION
FOR PAVING BITUMEN
|
Sr.No.
|
Charecteristics
|
Requirement
For Grades
|
Method
of Test
|
|
S35
|
S45
|
S55
|
S65
|
S90
|
S200
|
|
1.
|
Specific
Gravity at 27 deg C, min |
0.99
|
0.99
|
0.99
|
0.99
|
0.99
|
0.99
|
IS
1202:1978
|
|
2.
|
ater,
% by mass, max |
0.2
|
0.2
|
0.2
|
0.2
|
0.2
|
0.2
|
IS
1211:1978
|
|
3.
|
Flash
Point, Cleveland open Cup, deg C, min |
175
|
175
|
175
|
175
|
175
|
175
|
IS
1209:1978
|
|
4.
|
Softening
Point, deg C |
50-65
|
45-60
|
45-60
|
40-55
|
35-50
|
30-45
|
IS
1205:1978
|
|
5.
|
Penentration
at 25 deg C, 100g, 5 sec, in 1/10 mm |
30-40
|
40-50
|
50-60
|
60-70
|
80-100
|
125-225
|
IS
1203:1978
|
|
6.
|
Penentration
ratio, min |
35
|
35
|
35
|
35
|
35
|
35
|
-
|
|
7.
|
Ductility
at 27 deg C, cm, min |
50
|
75
|
75
|
75
|
75
|
-
|
IS
1208:1978
|
|
8.
|
Paraffin
wax content, % by mass, max |
4.5
|
4.5
|
4.5
|
4.5
|
4.5
|
4.5
|
IS
10512:1983
|
|
9.
|
Frass
Breaking Point, deg C, min |
-4
|
-4
|
-6
|
-6
|
-8
|
-10
|
IS
9381:1979
|
|
10.
|
Loss
on heating, thin film oven test, % by mass, Max |
1
|
1
|
1
|
1
|
1
|
1
|
IS
1212:1978
|
|
11.
|
Retained
penentration after thin flm oven test, 25 deg C, 100 g, 5 sec,
1/10mm, % of original, min |
55
|
55
|
52
|
52
|
47
|
42
|
IS
9382:1979
|
|
12.
|
Matter
soluble in trichloroethylene, % by mass, min |
99
|
99
|
99
|
99
|
99
|
99
|
IS
1216:1978
|
|
13.
|
Viscosity
at |
|
|
|
|
|
|
|
|
|
a.
60 deg C, Poise |
2500+/-500
|
2000+/-400
|
1500+/-300
|
1000+/-200
|
500+/-100
|
250+/-50
|
IS
1206 (Part 2):1978
|
|
|
b.135
deg C, cSt, Min |
220
|
210
|
180
|
150
|
110
|
20
|
IS
1206 (Part 3):1978
|
| |
|
|
|
|
|
|
|
|
|
Penentration
Ratio = (Penentration at 4 deg C, 200g, 60s/ Penentration
at 25 deg C, 100g, 5s) x 100
Paving
bitumen type 1 shall be classified into 6 grades according
to their penentration and each grade shall be given designation
as given in the table with letter "S" denoting the
type and a numeral representing the mean of the limits of
the penentration specified for the grade.
CONFORMS
TO IS:73-1992 SPECIFICATIONS FOR PAVING BITUMEN (TYPE 1) FROM
NON-WAXY CRUDE
|
|
Sr.No.
|
Charecteristics
|
Requirement
For Grades
|
Method
of Test
|
|
A35
|
A55
|
A65
|
A90
|
|
1.
|
Specific
Gravity at 27 deg C, min |
0.99
|
0.99
|
0.99
|
0.98
|
IS
1202:1978
|
|
2.
|
Water,
% by mass, max |
0.2
|
0.2
|
0.2
|
0.2
|
IS
1211:1978
|
|
3.
|
Flash
Point, Cleveland open Cup, deg C, min |
175
|
175
|
175
|
175
|
IS
1209:1978
|
|
4.
|
Softening
Point, deg C |
55-70
|
45-60
|
45-60
|
35-50
|
IS
1205:1978
|
|
5.
|
Penentration
at 25 deg C, 100g, 5 sec, in 1/10 mm |
30-40
|
50-60
|
60-70
|
80-100
|
IS
1203:1978
|
|
6.
|
Penentration
ratio, min |
25
|
25
|
25
|
25
|
-
|
|
7.
|
Ductility
at 27 deg C, cm, min |
10
|
15
|
15
|
15
|
IS
1208:1978
|
|
8.
|
Paraffin
wax content, % by mass, max |
10
|
10
|
10
|
10
|
IS
10512:1983
|
|
9.
|
Frass
Breaking Point, deg C, min |
-4
|
-6
|
-8
|
-10
|
IS
9381:1979
|
|
10.
|
Loss
on heating, thin film oven test, % by mass, Max |
1
|
1
|
1
|
1
|
IS
1212:1978
|
|
11.
|
Retained
penentration after thin flm oven test, 25 deg C, 100 g, 5 sec,
1/10mm, % of original, min |
57
|
57
|
47
|
42
|
IS
9382:1979
|
|
12.
|
Matter
soluble in trichloroethylene, % by mass, min |
99
|
99
|
99
|
99
|
IS
1216:1978
|
|
13.
|
Viscosity
at |
|
|
|
|
|
|
|
a.
60 deg C, Poise |
1000+/-300
|
400+/-300
|
300+/-10
|
200+/-50
|
IS
1206 (Part 2):1978
|
|
|
b.135
deg C, cSt, Min |
250
|
100
|
70
|
50
|
IS
1206 (Part 3):1978
|
| |
|
|
|
|
|
|
|
Penentration
Ratio = (Penentration at 4 deg C, 200g, 60s/ Penentration
at 25 deg C, 100g, 5s) x 100
Paving
bitumen type 2 shall be classified into 4 grades according
to their penentration and each grade shall be given designation
as given in the table with letter "A" denoting the
type and a numeral representing the mean of the limits of
the penentration specified for the grade.
CONFORMS
TO IS:73-1992 SPECIFICATIONS FOR PAVING BITUMEN (TYPE 2) FROM
WAXY CRUDE
|
|